Bucket Mortar SuperFlex Inserts
Mortar specially developed for the simultaneous grouting TABLETS OF GLASS AND PORCELAIN in internal and external environments, and special coating as saunas, pools, greenhouses (at a temperature of 65 ° C). Consisting of cimendo, aggregates and special additives. Available in assorted colors.
CONDITIONS OF FINISH: Parts of the coating must be clean, dry and free of residue or film to prevent contact of SuperFlex Inserts. The tablets should have a minimum size of 2x2 cm and maximum 7.5 x 7.5 cm.
CONDITIONS OF BASE: Cured at least 14 days (masonry, plaster and screed) and 28 days (concrete), clean, dry, flat, and strong enough. If they have powder residue, oils or leftover paint make your cleaning so as not to interfere with bonding of SUPERFLEX TABLET. If they have imperfections on the surface, they shall be repaired with a minimum of 48 hours before applying the coating. If the base does not present sufficient strength to eliminate it completely and redo it running 14 days after coating.
TOOLS AND ACCESSORIES: plastic trough, trowel, steel trowel 6 x 6mm (internal areas), 8x8 mm (external areas) wear on the lower teeth 1 mm, a container for measures, rubber hammer, jig flat wooden trowel rubber and personal protective equipment such as gloves, boots and goggles.
PREPARATION: Add water in the ratio indicated on the packaging. Knead vigorously until obtaining a homogeneous, consistent and doughy paste. The mixture to stand for 15 minutes (aging time) before application. Mix again without adding water and use up to two hours after preparation.
APPLICATION: Use the trowel extending flat side SUPERFLEX the tablet in an approximately 4 mm above the base layer, then forming beads and grooves on the toothed side. Also apply on the back of cards with the help of rubber trowel previously filling the joints, taking care not to leave excess material. For tablets together with dot of glue, do not pass mortar on the back, nods 8 x 8 mm trowel and grout them immediately after settlement with the mortar itself. Apply the plate previously pieced back together the adhesive mortar extended. Make a slight pressure with your hands and using the rubber mallet, wooden jig and completely crush the cords SUPERFLEX TABLET (not exceeding time of 10 minutes per step). Remove the paper on cards at least 60 minutes after laying and start cleaning with a clean damp sponge. After setting away some parts and see if your back is 100% of your completed by SUPERFLEX PAD area. 3 days after the settlement soak the coat with water and proceed to final cleaning of parts using superclean PARTS SPECIAL and a clean, damp sponge. Release to light traffic after 7 days for normal traffic and 14 days after settlement. In the case of swimming pools and tanks, filling after 7 days.
. Note: Apply small amounts to facilitate the coating limpeza.Nunca soaking with water before aplicação.Nunca strands that are based on secos.Nunca add more water to a mortar or already mixed beyond the use period of 2 horas.Em very porous and dry bases lightly moisten the base with structural água.Observar movimentação.Quando together and applied on external areas, do not apply in adverse weather conditions, such as bright sunlight or chuva.Utilizar skilled labor and under technical supervision. The liner pools must be initiated by the walls and the floor finalized.
6 to 8 kg / m
SAFETY: Keep out of reach of children and pets. In case of eye contact or accidental ingestion, seek medical advice immediately, taking this container.
STORAGE: About pallets in open, dry, airy location away 30 cm from the wall. Batteries should be a maximum of 1.5 meters in height.
SHELF LIFE: Maximum period of 18 months.
Balde 5 Kg
© 2013 by SuperMassa. All rights reserved.
Now the chat!
Learn about our companies
For technical support and financial affairs, open a ticket at our Customer Service by clicking here.
For sales questions, contact requests or suggestions, please complete the form below.